Connection adhesive ALL-IN-ONE - CONADH-(ALL-IN-ONE)-310ML

Connection adhesive ALL-IN-ONE - CONADH-(ALL-IN-ONE)-310ML - 1

Connection adhesive ALL-IN-ONE - CONADH-(ALL-IN-ONE)-310ML - 2

Connection adhesive ALL-IN-ONE

Name: Connection adhesive ALL-IN-ONE
Brand: Würth
SKU: 0893700111

Connection adhesive all-in-one ECOLINE
CONADH-(ALL-IN-ONE)-310ML

Art.-no. 0893700111

EAN 4056807105413

All versions

Prices for customers after login

Connection adhesive ALL-IN-ONE

Art.-no. 0893700111

Prices for customers after login

Quantity

Exclusively for trade customers

Login/Register
Call customer service: 045-488-4186

For the permanent sealing of all connection joints to ensure that they are air-tight and windproof and for fitting indoor and outdoor windows and doors.

Functional strength achieved rapidly

Can be used without clamping batten in line with DIN 4108-7 (2011-01) for joints and connections in new and renovated buildings.

Meets all DIN 4108-11 requirements

Guarantees rain-proof seals after curing

Achieves the necessary airtight connections/sealing of structural membrane.

Broad adhesive range

Outstanding adhesion properties to a wide range of construction materials and the relevant films

Bonding of sheets, films and tapes, even to slightly wet, dusty and absorbent surfaces

Good stability (thixotropic)

Does not drip off, even when used for vertical bonds.

Fills joints

Does not corrode metals

Compatible with paint

Silicone- and solvent-free

Our products featuring the EMICODE label are low-emission/low in harmful substances. The EMICODE classification system awards labels to construction products that comply with the very stringent health and environmental requirements of recognised institutes.

Proof of Performance

EMICODE EC1plus: Very low emissions: The EMICODE classification system distinguishes the environmental and health compatibility of construction products. The lowest-emission products bear the EC1plus mark.

Notice

Please refer to the processing instructions of the system warranty.

When adhering films and strips in outdoor applications, despite the largely favourable "resistance to rain immediately after application of the ALL-IN-ONE connection adhesive", it must be ensured that intensive moisture exposure, e.g. through continual rain, moisture run-off, is excluded.

Cured ALL-IN-ONE connection adhesive has good water resistance; nevertheless, applications where there is a constantly increased level of humidity, e.g. swimming pools or other wet areas (due to the aggressive chlorine-containing moist air, among other factors), should be avoided. Not suitable for bonding pool linings.

The time parameters specified here can only be determined precisely by in-house tests, as they are greatly affected by material, temperature, application quantity, humidity, material humidity, adhesive film thickness, press pressure and other criteria. As a rule, corresponding safety margins are provided for the reference values.

Application area

Construction material	Vol. %
Examples of the material humidity of the building materials as orientation values:
Clay brick	≤ 2.5
Plaster	≤ 5
Dry removal plates	≤ 5
Concrete	≤ 5
Gas concrete	≤ 8
Wood	≤ 12

Application quantity/adhesive yield
Adhesive bead diameter	310 ml cartridge	600 ml bag
4 mm	24.7 rm	47.7 rm
5 mm	15.8 rm	30.6 rm
6 mm	11.0 rm	21.2 rm
7 mm	8.1 rm	16.6 rm
8 mm	6.2 rm	11.9 rm

The usage instructions are recommendations based on the tests we have conducted and on our experience; carry out your own tests before each application. Due to the large number of applications and storage and processing conditions, we do not assume any liability for a specific application result. Insofar as our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting deliberately. We guarantee the consistent quality of our products. We reserve the right to make technical changes and further develop products. Please observe the technical data sheet!

Product information

Würth Catalogue

Datasheets(X)

Certificates/ Documents

Application area

Permanently elastic, airtight joint, component connection and impact overlap bonding/sealing of vapour barriers, vapour retarders, sealing films in dry construction (except for swimming pool areas) and all WÜTOP non-breathable membranes, breathable membranes, façade membranes and WÜTOP thermal membranes to be used only on the non-woven side.

Bonding/sealing of water-vapour-impermeable and permeable sealing tapes when installing windows and doors on absorbent surfaces.

Instructions

The base material must be clean, dry and free of grease. For pre-treatment, refer to the technical data sheet.

Cut off the thread cap, screw on the nozzle and cut it to the required width. Apply the adhesive using a suitable application gun.

The adhesive is applied on one side (as a 4-8 mm thick bead) to the film or the load-bearing construction material (can also be applied to slightly damp, dusty or absorbent surfaces).

The film is then bonded (with a discharge loop for strain relief) while the adhesive bead is still wet and pressed lightly to fix in place (do not press the bead flat, the ≥1 mm thickness should be retained).

Detached compounds can be joined together once again due to the self-adhesive properties of the adhesive.

Container	Cartridge
Chemical basis	Acrylate polymer dispersion
Colour	Light blue
Density/conditions	1.02 g/cm³ / at 20°C, EN 542
Min. final strength	48 h
Min./max. processing temperature	-5 to 40 °C
Min./max. processing temperature for cartridge	10 to 35 °C
Min./max. temperature resistance	-30 to +120 °C
Shelf life from production/conditions	24 Month / cool and dry storage area, no exposure to sunlight, 15°C to 25°C
Weight of content	316 g
Solvent-free	Yes
Contents	310 ml
Silicone-free	Yes
Sustainability	Pollutants / Emissions

Additional accessory:

Product

Description

Quantity

Price
/PU

Underlays WÜTOP<SUP>®</SUP> Thermo ND Plus

Underlays WÜTOP® Thermo ND Plus

ROOFSTR-THERMO-ND-PLUS-2SK-75SM

WUETOP

Art.-no. 0681001037

The perforation-proof polyester roof protection film

x 75 m²

The packaging unit defines the number of articles in one packaging. In the catalog segment you can choose from different packaging units if a pop-up menu is displayed.

Just leave the field empty if you don't know the packaging unit when directly entering the article number in the shopping basket or when importing with Easy-/VarioScan. The packaging unit will be determined automatically.

The article number is made up of the following: VVVVAAABBB
VVVV = 4 digits for prefix number (please note that the first digit is currently always 0)
AAA = 3 digits for dimension part 1
BBB = 3 digits for dimension part 2

Example article number structures:
Example 1: Screw with dimensions of 4x10 mm:
VVVVAAABBB
00574 10 (2 spaces between the 4 and the 10)

Example 2: Screw with dimensions of 10x20 mm:
VVVVAAABBB
005710 20 (1 space between the 10 and the 20)

Example 3: Flat washer with an internal diameter of 6 mm:
VVVVAAABBB
04076

Price per packaging unit (PU):
The displayed price is always in line with the displayed packaging, if the PU is 250 the price for 250 units, if the PU is 300 the price for 300 units.

Price with price key representation (PSL):
The price always applies to a quantity ruled through the price key:
Price for 1 unit
Price for 100 units
Price for 1000 units

The quantity shows the number of pieces or units of measure contained in the order or delivery for the respective article.

In contrast to sales packaging and secondary packaging, the disposal costs for chemical-technical products are shown separately. The breakdown of the individual costs can be found on the relevant products and also in the shopping cart, as well as in our General Terms and Conditions (GTC).